Tesamorelin Dosage Calculator & Chart
Printed on the vial label.
1 mg = 1,000 mcg. Enter your own prescribed or planned amount.
Draw on your syringe
80units= 0.8 mL
- Concentration
- 2,500mcg/mL
- Each unit
- 25 mcg
- Doses per vial
- 2
- Vial lasts
- 2days
Want a rounder number to draw?
Show the math
- Concentration = 5 mg × 1,000 ÷ 2 mL = 2,500 mcg/mL
- Volume = 2,000 mcg ÷ 2,500 mcg/mL = 0.8 mL
- Units = 0.8 mL × 100 = 80 units (U-100: 100 units = 1 mL)
The pre-filled dose (2 mg) is an example input so the calculator shows a result. It is not a recommendation.
Tesamorelin units chart
Units to draw on a U-100 syringe for common Tesamorelin vial sizes, each mixed with 2 mL of bacteriostatic water. Change the water in the calculator and this table updates.
| Dose | 2 mg vial | 5 mg vial | 10 mg vial |
|---|---|---|---|
| 500 mcg | 50 | 20 | 10 |
| 1 mg | 100 | 40 | 20 |
| 2 mg | >100 | 80 | 40 |
Values are units on a U-100 insulin syringe (100 units = 1 mL). ">100" means the dose does not fit in a 1 mL syringe at this dilution.
About Tesamorelin
Tesamorelin is a growth-hormone-releasing hormone (GHRH) analog, FDA-approved as Egrifta to reduce excess abdominal fat in adults with HIV-associated lipodystrophy.
Regulatory status: FDA-approved (Egrifta) for a specific indication. Use only as prescribed. "Research" vials are not FDA-approved products.
Also searched as: Egrifta.
How to reconstitute Tesamorelin
- Wash your hands and let the vial reach room temperature.
- Wipe the rubber stoppers of the peptide vial and the bacteriostatic water with an alcohol pad.
- Draw the planned amount of bacteriostatic water (for example 2 mL — that is 200 units on a 1 mL syringe).
- Inject the water slowly down the inside wall of the vial, not directly onto the powder.
- Gently swirl or roll the vial until the powder dissolves. Do not shake.
- Label the vial with the date and the concentration shown by the calculator, and store it as the product label directs (reconstituted peptides are normally kept refrigerated).
These are general handling steps, not medical instructions. If your product came with instructions from a pharmacy or prescriber, follow those.
What you need
Bacteriostatic water
Sterile water with 0.9% benzyl alcohol, used to dissolve the powder.
U-100 insulin syringes
0.3 mL syringes are easiest to read for small doses; 1 mL for larger ones.
Alcohol prep pads
Wipe the vial stopper before every draw.
Sharps container
For safe disposal of used needles.
- Which syringes and supplies to buy →
Tesamorelin calculator FAQ
How many units is 2 mg of Tesamorelin?
+
It depends on how much water you add. With a 5 mg vial mixed with 2 mL of bacteriostatic water, the concentration is 2,500 mcg/mL, so 2 mg is 0.8 mL = 80 units on a U-100 insulin syringe. With a 10 mg vial and the same 2 mL of water it is 40 units.
How much water should I add to a 5 mg Tesamorelin vial?
+
The water volume does not change the total amount of Tesamorelin; it only sets the concentration. Common choices are 1–3 mL. With 2 mL, each unit on a U-100 syringe holds 25 mcg. Pick a volume that makes your dose easy to read on the syringe — the calculator above suggests volumes that land on round numbers.
How many doses are in a 5 mg vial of Tesamorelin?
+
At 2 mg per injection, a 5 mg vial contains 2 full doses. The amount of water you add does not change this number.
Is Tesamorelin approved?
+
FDA-approved (Egrifta) for a specific indication. Use only as prescribed. "Research" vials are not FDA-approved products.
Sources
Calculator math: concentration = vial mg × 1,000 ÷ water mL; units = dose ÷ concentration × 100 (U-100 syringe). Data and references last reviewed 2026-10-10.